Description
The Unisens E is a pure telemetry sensor especially for all electric models. He is so small and light, but at the same time so powerful that it can be used in almost every model.

Telemetry is used must be specified in Unisens E only once in the settings. This is done either through our PC program "Unisens E Tool" or the UniDisplay. On delivery HoTT GAM is selected.

To change the settings via PC or for firmware updates a suitable USB interface or an existing USB connection cable as of Jeti, multiplex or Graupner is necessary. See also the instructions.

The Unisens E can measure the complete drive without additional sensors, ie voltage, current, capacity and even speed. A special attraction is in fact already a Brushless Speed ​​Sensor permanently installed. A small cable connects to one of the three motor phases only have to be made with the supplied cable for measuring the speed.

As a barometric (atmospheric pressure) level sensor is integrated with high resolution, a Vario with the Unisens E is implemented in addition to the height measurement.

Similarly extensive alarms can be programmed to be reported via telemetry through the respective stations.

The Unisens E is available with various connection systems, so that normally nothing needs to be soldered. The current measuring range is symmetrical in both directions. This makes the pin assignment, so that the battery male or female has the positive terminal, not matter. The measuring direction is just simply set in the setup.

About our UniDisplay all readings of Unisens E can be viewed directly live and all settings and alarms can be programmed.

Whether sailors, Stunt Plane, helicopter, HLG or Slowflyer who Unisens E can be used due to its light weight and compact size in almost every area. Of course the Unisens E is suitable not only for airplanes. It can be installed as well in RC boats, RC cars and so on.

You buy the Unisens E a powerful in all respects universal RC telemetry sensor, whichthe modern electronics exploits to you as a little helper to be a great help in dealing with your RC models.

Update with S8344 and 7168.6 possible.

Features

    Complete measurement of electric drives with current, voltage, power, capacity, speed and altitude measurement
    integrated brushless speed sensor
    full telemetry support for Jeti Duplex (EX), Multiplex M-Link, Graupner HoTT, Robbe / Futaba FASSTest S.BUS2, JR DMSS and FrSky
    Height measurement with automatic zeroing after switching
    barometric Vario
    Current measurement range up to 140 A in both directions, voltage up to 60 V
    (The maximum current carrying capacity of the connectors used must not be exceeded!)
    Connection for signal receiver for the remote control of certain functions
    direct connection to the GPS logger possible to record data in a file
    Measurement of receiver battery voltage
    Powered by receiver
    current status is indicated by LED
    direct viewing of live or recorded readings with our UniDisplay
    Parameter settings via PC, UniDisplay and telemetry possible
    free firmware updates via the PC USB connection cables with existing as of Jeti, multiplex or Graupner possible
    use due to its compact size and low weight almost anywhere



Delivery

    Unisens E with integrated height sensor / Vario
    Receiver cable for telemetry / power supply
    Connection cable for brushless speed measurement
    detailed colored manual



Specifications

    Current measurement range: 140 A in both directions, so - 140 A to 140 A +
    The following stress periods are permissible:
    - 100 A indefinitely
    - 120 A for 1 minute
    - 140 A for 20 seconds
    Depending on the plug-in system but are the limits of the plug significantly lower!
    Reasonable values ​​are here:
    - MPX green (double contact) and XT60 Duration: 50 A / 20s: 70 A
    - 4mm Gold Plug Duration: 80 A / 20s: 100 A
    - 5.5 mm gold plug length: 120 A / 20s: 150 A
    Voltage measurement range: 0 to 60 V
    Height measurement range: 0 to 8000 m NN, when switching is automatically reset
    Receiver voltage measurement: 3.8 V to 10 V
    Data Rate: 10 Hz
    Power supply: from receiver supply via telemetry connection "Link" (from 3.8 V up to 10 V)
    Power consumption: 25 mA
    External connections: 1 connection times for telemetry and power ("Link")
    1 times phase connection for Brushless Speed ​​measurement
    1 times servo pulse input from the receiver
    COM port for UniDisplay, GPS logger or PC
    Dimensions: green MPX connector: 26 (38) x 29 x 9 mm
    yellow XT60 connector: 26 (50) x 29 x 9 mm
    4mm gold connector: 26 (55) x 22 x 9 mm
    5.5 mm gold plug: 26 (44) x 22 x 11 mm
    6 mmLMT Goldconnector: 26 (42) x 22 x 11 mm
    Mass: 10 g - 14 g without cable (depending on the plug-in system), connection cable 4 g